Pre-Purchase Inspection Services

Every inspection, every detail, fully in-house

Every pre-purchase and warranty inspection is performed directly by an independent master inspector—in-person and on-site. No subcontractors, no outsourced reports, no post-purchase surprises.

Schedule An Inspection

call or text (386) 320-3023

Mobile Pre-Purchase Vehicle Inspection Services

We complete most inspections same-day or within 24 hours (Monday–Friday), depending on seller and owner availability.

Standard Vehicle Inspection

For vehicles up to 15 years old (including hybrids).
Model years 2011 and newer.

OBD2 ECU Computer Diagnostics
Scan all control modules for active, pending, or historical Diagnostic Trouble Codes (DTCs), and verify emissions monitor readiness status.
Engine Compartment & Drive Belts
Inspect serpentine/drive belts for cracking, check valve covers for oil seepage, and assess timing belt/chain cover seals.
Brake System Components
Inspect brake pad lining thickness, check rotor surfaces for scoring/rust lip, inspect rubber flex lines for cracks, and inspect brake fluid condition.
Suspension & Steering Wear
Inspect control arm bushings, ball joints, sway bar links, tie rod ends, and struts/shocks, check for torn grease boots, inspect for hydraulic leaks.
Tire Tread & Date Codes
Measure tread depth across all tires, inspect for uneven alignment wear, and verify the 4-digit DOT manufacture date code to check for age dry-rot.
Electrical System & Charging
Test battery cold cranking amps (CCA), check terminal corrosion, measure alternator charging voltage under load, and test all exterior lighting.
Cooling System Integrity
Inspect the radiator and cap, inspect upper/lower radiator hoses for soft spots or swollen ends, and check for water pump shaft play or leaks.
Underbody Frame & Fluid Leaks
Inspect unibody pinch welds, frame rails, and rocker panels for structural rust; check engine oil pan, transmission pan, and differential seals for leaks.
Engine Air Filter & Intake
Inspect engine air filter, check intake boot bellows for dry-rot cracking, and inspect throttle body housing for carbon buildup.
Instrument Cluster & Cabin Controls
Verify instrument panel bulb check at key-on, test HVAC heating/cooling blend door operation, and ensure proper function of power windows, locks, windshield wipers and washer.

$200

Vintage & Classic Vehicle Inspection

For vehicles 16+ years old (including hybrids).
Model years 2010 and older.

Carburetor & Fuel System Integrity
Inspect the mechanical fuel pump and carburetor, verify choke setup, and examine rubber fuel lines for ethanol degradation.
Drum & Disc Hydraulic Brakes
Inspect single/dual-reservoir master cylinders for fluid leaks and check rubber flex lines for dry rot.
Ignition System & Timing
Inspect distributor cap, spark plug wires, and vacuum lines for degradation.
Chassis Frame, Subframe & Torque Boxes
Examine full perimeter frame rails, unibody subframe connectors, crossmembers, and torque boxes for severe rust scale, past accident alignment, or improper patch welds.
Floor Pans, Trunk Pan & Rocker Panels
Check driver/passenger footwells, inner rocker panels, lower quarter panels, and spare tire wells for structural rust, fiberglass repairs, or pop-riveted sheet metal patches.
Body Filler (Bondo) & Paint Assessment
Inspect body for excessive body filler thickness around wheel arches, lower door skins, and quarter panels; check for paint bubbling, checking, or clearcoat lifting.
Steering Gearbox & Mechanical Linkage
Inspect manual or early power steering boxes for excessive center gear play, check Pitman arm, Idler arm, drag link, and tie rod ends for grease boot failure and joint looseness.
Wiring Harness & Electrical Relays
Check glass fuse blocks for corrosion, inspect cloth-braided or aging vinyl wiring for brittle insulation/exposed copper, and verify non-factory aftermarket wiring splices.
Leaf Springs & Suspension Bushings
Inspect multi-leaf rear springs for broken leaves or sagging, check front control arm rubber/polyurethane bushings for cracking, and verify shock absorber dampening integrity.
Brightwork, Body Trim & Glass Seals
Check chrome bumpers, stainless steel trim, and pot-metal grilles for pitting, plating peel, or missing clips; inspect vent window rubber, windshield lock-strip seals, and weatherstripping for water leaks.

$235

Luxury, Exotic, & Supercar Vehicle Inspection

Applies to luxury, exotic, and high-performance supercars.

Carbon Fiber Monocoque & Subframe Tub
Inspect exposed carbon weave for stress fracturing, delamination, or repair seams; check aluminum/titanium front and rear subframes for structural distortion or curb damage.
Carbon Ceramic Brake System (CCM/CCB)
Inspect ceramic rotors for material oxidation, check rotor faces for edge chipping or hot spots, and inspect brake rotors and pads.
Dual-Clutch / E-Gear Transaxle & Clutch Wear
Run specialized diagnostic software checks, perform a road test if applicable, and inspect for transaxle case fluid weeping.
Proprietary ECU Diagnostics & ECU Logs
Perform deep module scans using factory-level tools to check over-rev counters (Range 1–6 ignitions), launch control activation counts, tuning flash status, and historical fault memory.
Front Axle Nose-Lift System
Test hydraulic or pneumatic front suspension lift actuators, checking pump pressure lines, reservoir fluid levels, and height sensor response times to ensure ground clearance operation.
Active Aerodynamics & Airbrake Hydraulics
Cycle deployable rear wings, active front diffusers, and airbrakes to verify hydraulic ram seals, electric actuator alignment, and high-speed deployment sensor fault status.
High-Stress Thermal Management & Engine Bay Seals
Inspect twin-turbo/supercharged heat shields, engine cover glass seals, dry-sump oil tank fittings, and rubber hose heat-soak degradation under high engine bay temperatures.
Exhaust System & Catalytic Converter Modifications
Check for aftermarket cat-back or straight-pipe exhausts, inspect valved exhaust vacuum solenoids, and verify O2 sensor spacers or cat-delete tunes.
Paint Finish, Carbon Trim & PPF Installation
Inspect Paint Protection Film (PPF) edges for lifting/yellowing, and check exposed exterior carbon fiber for UV resin hazing.
Bespoke Interior Materials & Electronics
Check Alcantara and hand-stitched leather panels for dash shrinkage or UV lifting, verify carbon interior trim clearcoat cracking, and test specialized infotainment, telemetry systems, and digital dashboards.

$275

Electric Vehicle (EV) Inspection

Applies to all fully electric vehicles (EVs).

High-Voltage Battery Health & Enclosure
Scan the Battery Management System (BMS) for State of Health (SOH), cell voltage imbalances, and inspect the underbody battery pack tray for impact dents, structural breaches, or seal compromise.
Thermal Management & Liquid Cooling
Check low-conductivity coolant levels, inspect electric water pumps and directional valves for leaks, and verify radiator/chiller thermal performance during active fast charging or heavy load.
Charge Port Assembly & Latching
Inspect J1772, CCS, or NACS (SAE J3400) port pins for thermal damage, arc pitting, or moisture ingress; verify motorized lock pin engagement and onboard AC charger handshake.
Regenerative Braking & Mechanical Rotors
Test blended regenerative braking transitions and check steel rotors for excessive rust or pitting caused by low mechanical brake utilization.
Electric Drive Unit & Reduction Gearbox
Inspect front/rear drive units for high-voltage isolation faults and check axle shaft seals for oil weeping.
High-Voltage Cabling & Manual Service Disconnect (MSD)
Verify orange HV cable insulation integrity, inspect connector locking levers, check grounding straps for corrosion, and ensure the manual service disconnect is secure.
Inverter & Power Electronics
Scan the traction inverter, DC-AC power module, and onboard charging module (OBC) for active DTCs, thermal throttling codes, or isolation degradation warnings.
Heat Pump & Cabin Climate Control
Test heat pump operation, PTC electric cabin heater output, octovalve/manifold coolant switching, and compressor performance in heating/cooling modes.
EV-Specific Load Tires & Alignment
Measure tread depth for accelerated inner-shoulder wear caused by high curb weight and instantaneous electric torque; verify HL/XL load-index rating compliance and foam liner integrity.
12V/48V Auxiliary Battery & DC-DC Converter
Test the low-voltage lead-acid or LiFePO4 auxiliary battery condition, and verify the DC-DC converter output voltage under high system load.

$275

Light & Commercial Trailer Inspection

Covers light-duty to heavy-duty towable trailers used for commercial, equipment, and utility transport.

Coupler, Latch & Safety Chains
Inspection of ball coupler, pintle ring, or gooseneck hitch for wear, locking mechanism functionality, safety chain link integrity, and rated hooks.
Emergency Breakaway Safety System
Testing the pull-pin switch, safety cable, and dedicated 12V onboard breakaway battery charge level.
Frame Rails, Crossmembers & Welds
Structural check for frame twist, stress fractures, rust-through, bent crossmembers, and main beam weld integrity.
Decking & Floor Board Condition
Evaluating wood rot, steel plate corrosion, cracked aluminum, or soft spots under heavy load areas.
Axles, Leaf Springs & Suspension Hardware
Checking axle straightness, leaf spring pack condition, equalizer bushings, hangers, and u-bolts.
Brake Shoes, Drums & Magnets
Verifying electric magnet functionality and hydraulic surge actuator fluid.
Wheel Bearings, Hubs & Grease Seals
Checking for hub play, noisy or hot bearings, grease seal leaks, and dust cap security.
Tire Load Rating, Tread & Sidewall Condition
Checking DOT date codes, sidewall cracking, uneven tread wear indicative of bent axles, and load range rating against trailer GVWR.
Hydraulic Pump, Cylinder & Lift Mechanisms (Dump/Tilt)
Inspecting dump hydraulic power units, fluid levels, hose condition, lift cylinder seals, and frame hinge pins.
DOT Lighting, Wiring Harness & Trailer Plug
Verification of 7-way/4-way plug connectors, wiring harness routing/protection, tail/brake/turn lights, and side marker clearance lamps.

$300

Mobile Pre-Purchase Recreational Vehicle Inspection Services

Pop-Up Camper Trailer Inspection

Applies to all pop-up camper trailer models.

Lift System Cables, Pulleys & Winch
Inspect steel lift cables for fraying or rust, check pulley alignment, inspect the main winch/crank mechanism, and test the safety ratcheting system during extension and retraction.
Canvas, Vinyl & Screen Integrity
Check fabric tenting for tears, dry-rot, mold, or seam separation; inspect clear vinyl window panels for cracking and test all window zippers for binding.
Bed Slide Rails & Support Posts
Extend bunk ends to inspect slide rollers and channel tracks for binding or debris; verify support poles lock securely into bumper and tongue frame brackets.
Hard Roof Shell, Gaskets & Latches
Inspect ABS or aluminum roof caps for stress cracks, delamination, and seam sealant failure; check perimeter rubber weather gaskets and verify roof corner tie-down latches seal tight.
Subfloor & Corner Wood Rot
Inspect interior floor corners, under-dinette storage compartments, and bottom underbelly plywood for soft spots, water staining, or delamination caused by road spray or canvas leaks.
3-Way Refrigerator Operation
Test the absorption refrigerator on 120V AC, 12V DC, and LP Gas modes, checking rear burner flue cleanout and flame ignition safety thermal coupler.
Propane System & Regulator Pressure
Inspect liquid propane (LP) gas lines, inspect rubber pigtail hoses for cracking, and check dual-stage regulator pressure output.
Axle, Leaf Springs & Tire DOT Age
Inspect single-axle leaf springs and shackles for rust scaling, test electric brake magnets (if equipped), and verify tire DOT age codes for dry-rot.
Fresh Water Tank, Hand Pump & Lines
Inspect low-pressure PEX/vinyl lines, test 12V water pump or manual sink hand-pump operation, and check the fresh water holding tank and drain valve for cracks.
A-Frame Chassis, Coupler & Electrical Harness
Check the front A-frame tongue welds for structural rust, verify coupler latch locking pins and safety chains, and test 7-way/4-way trailer wiring harness lighting outputs.

$300

Standard Recreational Vehicle (RV) Inspection

Applies to all standard travel trailers, campers, and RVs.

Roof Membrane & Lap Sealant
Inspect TPO, EPDM, or fiberglass roof surfaces for tears, puncture damage, soft spots, and check self-leveling lap sealant around vents, skylights, and end-caps for cracks or void gaps.
Slide Out Mechanism & Weather Seals
Test slide out extension and retraction for smooth operation, checking hydraulic/electric motors, alignment tracks, wiper seals, and rubber bulb gaskets for dry-rot or water leaks.
12V DC & 120V AC Electrical Systems
Verify shore power transfer, main breaker panel, 12V converter/charger output, inverter function, GFCI receptacles, and house battery bank health/voltage holding.
Plumbing System & Water Heater
Inspect water lines for leaks, inspect water pump operation, test grey/black holding tank dump valves, and inspect the water heater tank and bypass valves.
Propane (LP Gas) System & Leak Check
Check dual-stage regulator pressure output and inspect rubber pigtail hoses and appliance control valves.
HVAC & Roof Air Conditioning
Test heat strip/furnace combustion blowers and verify air conditioning performance in cooling mode.
Onboard Generator Operation
Check generator oil level, air filter, fuel line connections, exhaust manifold security, hour meter reading, and test output performance under full load (running both AC units).
Chassis Frame & Underbelly Enclosure
Examine main frame rails and crossmembers for rust or weld cracks; inspect enclosed belly pan material (Coroplast) for sagging, road damage, or unsealed plumbing penetrations.
Hydraulic/Electric Leveling Jacks
Cycle auto-leveling systems to check leg pad landing gear, inspect hydraulic rams for fluid weeping, check motor solenoid relays, and verify height limit sensors.
Interior Moisture & Delamination Check
Inspect for signs of moisture around ceiling vents, wall corners, slide out surrounds, and window frames to check for wall delamination and subfloor rot.

$400

Toy Hauler Trailer Inspection

Applies to all toy hauler trailer models.

Rear Ramp Door, Spring Assists & Gaskets
Inspect heavy-duty ramp door hinges, assist cables, and spring tensioners; test perimeter rubber bulb weatherstripping for water leaks, and check the ramp deck for soft spots or internal wood rot.
Onboard Fuel Station & Pump System
Check the auxiliary fuel tank mounting, static grounding wire, fuel hose nozzle, and transfer pump motor operation; test the emergency shut-off switch and inspect the fuel gauge for proper readings.
Onboard High-Output Generator System
Test the gas or LP generator under high load (running multiple AC units), inspect the exhaust pipe routing and heat shielding, verify oil levels, and check transfer switch operation.
Garage Floor Decking & Tie-Down D-Rings
Inspect rubberized/oil-resistant garage floor coatings for gouges or lifting, and verify that all flush-mounted D-ring tie-down anchors are structurally bolted into frame crossmembers.
Garage Vapor Wall & Passive Venting
Check glass sliding doors and rubber sweep seals separating the garage from the living area; test high/low sidewall flow-through fuel vapor vents to ensure exhaust fumes vent outside properly.
Roof Membrane, Walkable Decking & Sealant
Inspect walkable TPO/PVC roof surfaces for tears, punctures, or soft spots caused by heavy foot traffic, and check lap sealant around air conditioners, vents, and roof rack mounts.
Heavy-Duty Tandem/Triple Axles & Tires
Inspect 7,000+ lb capacity axles, leaf springs, and heavy-duty shackle links for wear; check tire load ratings (E/F/G range), DOT age codes, and test electric/hydraulic brake operation.
Heavy-Duty I-Beam Frame & Underbelly Integrity
Examine the main chassis rails and extended hitch frame for metal fatigue, weld cracks, or flex; inspect the enclosed underbelly pan for sagging, damage, or loose mounting hardware.
Hydraulic Auto-Leveling System & Landing Gear
Test 4-point or 6-point hydraulic leveling jacks under heavy tongue/pin loads, checking hydraulic ram chrome shafts for scoring, fluid leaks, and pump manifold pressure.
High-Capacity Plumbing, Tanks & Dump Valves
Inspect oversized fresh water tanks and dual grey/black holding tanks for mounting strap stress; test grey/black waste termination valves and flush system connections for leaks.

$400

Fifth-Wheel Camper Trailer Inspection

Applies to all fifth-wheel camper trailer models.

Kingpin Box & Hitch Assembly
Check the kingpin for excess scoring, cracks, or warping; verify mounting bolts, safety latching mechanisms, and breakaway switch wiring.
Roof Membrane & Lap Sealant Condition
Inspect TPO/EPDM/PVC membrane for tears, bubbling, or chalking, and ensure lap sealant around vents, skylights, and end-cap seams is pliable without cracks.
Slideout Operation & Bulb Seals
Test hydraulic or electric drive mechanisms for binding; inspect wiper seals, bulb seals, and top sweep seals for rubber dry-rot or alignment gaps.
Axles, Suspension & Tire Condition
Check coil and leaf springs, equalization shackles, and bushings for wear or cracking; verify tire DOT age codes, tread depth, and sidewall checking.
Electrical Systems (12V DC & 120V AC)
Test shore power transfer, 50-amp main breaker panel, 12V converter/charger output, battery bank health, and GFCI receptacle ground faulting.
Plumbing System Pressure & Holding Tanks
Inspect water lines, the water heater, and check grey/black holding tank dump valves for leaks.
Frame Integrity & Underbelly Enclosure
Inspect main I-beam chassis rails for flex or weld fractures, checking corrugated belly pan material (Coroplast) for sagging or water traps.
Landing Gear & Hydraulic Leveling Jacks
Run automatic/manual leveling jacks to check for fluid leaks, bent inner legs, foot pad welds, and landing gear motor condition.
Patio Awning & Hardware Mechanisms
Deploy power or manual awnings to check fabric tension, arm alignment, pitch adjustments, and electric motor operation.
Interior Ceiling & Wall Water Intrusion
Inspect for signs of moisture around slide out corners, over-cab bed areas, ceiling vents, and window frames.

$500

Class C Motorhome Inspection

Applies to all Class C motorhome models.

Over-Cab Bunk Structure & Window Seals
Check the cab-over overhang for soft spots, wood rot, or delamination caused by leaks at the front clearance lights, escape window, or cab transition seam.
Chassis Drivetrain & Engine Bay
Scan the OEM engine (Ford E-Series/Chevy Express/Sprinter) for OBD2 codes, inspect fluid conditions, check belt/hose wear, and test transmission shift engagement.
Roof Membrane & Cab Transition Seam
Inspect TPO, EPDM, or fiberglass roof caps for tears and soft spots; focus on self-leveling lap sealant where the house roof joins the front cab superstructure.
Slide Out Mechanism & Weather Seals
Cycle room extensions to check electric/hydraulic motors and track alignment; inspect inner and outer wiper/bulb gaskets for dry rot or gaps.
Onboard Gas/LP Generator
Check oil level, fuel line fittings, exhaust pipe heat shielding, hour meter, and verify steady 120V AC output under load (running the rooftop AC unit).
House Battery Bank & Electrical Converter
Test 12V deep-cycle battery health, check terminal corrosion, verify 120V AC shore power transfer, and measure converter/charger charging voltage output.
PEX Plumbing System & Water Heater
Inspect hot/cold water lines, test 12V water pump flow, check waste dump valves, and inspect the water heater tank.
ASME Chassis Propane Tank & Regulator
Inspect the liquid propane (LP) gas system, check regulator output pressure, and inspect the frame-mounted ASME tank for rust scale or shut-off valve damage.
Dual Rear Wheels (DRW) & Suspension
Inspect rear dual tires for tread depth and DOT age codes, check inner-wheel valve stem extensions, and evaluate leaf springs and helper airbags for sagging.
Stabilization & Leveling Systems
Cycle automatic hydraulic or electric leveling jacks to check ram extension, fluid reservoir levels, pressure hose weeping, and foot pad weld security.

$450

Class B Motorhome Inspection

Applies to all Class B motorhome models.

Pop-Top Roof Mechanicals & Canvas
Test pop-top hydraulic struts, safety latches, canvas tenting for tears or mold, and inspect the rubber perimeter seal for water intrusion.
OEM Van Chassis Drivetrain
Perform an OBD2 system scan on the Sprinter, Transit, or ProMaster chassis, check fluid conditions, inspect drive belts, and test engine/transmission performance.
High-Capacity Lithium / AGM Battery Bank
Inspect state of charge, Battery Management System (BMS) communications, second alternator/under-hood generator output, and DC-to-DC charger operation.
Sliding & Rear Cargo Door Seals
Check main sliding door rollers and track alignment, test rear cargo door hinges, and inspect continuous rubber weatherstripping for pinch damage or air leaks.
Hydronic / Fuel-Fired Heating Systems
Test diesel/gasoline-fed hydronic heat exchangers or furnace units, checking fuel tap lines, inspect coolant loop and exhaust port heat shielding.
Cassette / Marine Toilet & Grey Water Setup
Inspect cassette toilet holding tank seals and valve blade operation, check fresh water fill lines, and test low-profile grey water tank dump valves.
Roof Rack, Solar Panels & Roof Penetrations
Check solar panel mounting brackets, wiring gland entry seals, roof rack track fasteners, and self-leveling sealant around power vent fans.
Undermount Tanks & Ground Clearance
Inspect chassis-mounted freshwater/greywater tanks, LP tanks, and generator housings for rust, mounting strap security, and adequate road clearance.
Suspension Upgrades & Tire Ratings
Evaluate aftermarket leaf springs, sumo springs, or Fox/Van Compass shocks; verify tire load index ratings (E/XL) and inspect inner shoulder tread wear.
Cabinetry Latches & Lightweight Modular Build
Test positive-locking marine push-latches, track-mounted seating systems, folding bed frames, and lightweight aluminum/plywood cabinet structural rigidity.

$500

Class A Motorhome Inspection

Applies to all Class A motorhome models.

Chassis & Drivetrain Performance
Scan engine ECM/TCM for fault codes, check fluid condition in gas (V10/V8) or diesel pusher (Cummins/Caterpillar) engines, and inspect the Allison transmission, radiator pack, and drive belts.
Air Brake & Air Suspension Systems
Perform an air brake test, verify compressor operation, inspect air springs/bags, and check automatic drain valves and desiccant air dryers.
Roof Structure & End-Cap Transitions
Inspect molded fiberglass or TPO roof surfaces for cracks, soft spots, and check self-leveling lap sealant around A/C shrouds, satellite dishes, and front/rear cap seams.
Multi-Room Slide Out Systems
Test heavy hydraulic or rack-and-pinion slide mechanisms, inspect alignment, check hydraulic rams for fluid leaks, and evaluate inner/outer bulb seals.
Onboard Commercial Generator
Check oil levels, fuel lines, exhaust routing, and test the 8kW–12kW generator under full electrical load (running all rooftop A/C units simultaneously).
50-Amp Electrical & Inverter System
Inspect the 50-amp main breaker panel, test automatic transfer switch (ATS) operation, verify pure sine wave inverter/charger output, and test house battery bank voltage under load.
Hydronic Heating / HVAC Systems
Inspect Aqua-Hot or Oasis fuel-fired/electric hydronic heating loops for coolant leaks, check heat exchanger zones, and test dual/triple basement or roof heat pumps.
Automatic Leveling Jacks
Cycle 4-point hydraulic leveling jacks to check ram extension, foot pad welds, fluid reservoir level, and pressure valve manifold integrity.
One-Piece Windshield & Frame Alignment
Check large panoramic windshields for cracks, stress pops out of the rubber gasket, or glass seal separation caused by chassis flex.
Bus Chassis Axles, Tag Axle & Tires
Check 22.5″ tire DOT age codes and sidewall cracking and inspect steer/drive/tag axle air bags and shocks.